初心者はどのようにCCNP認定資格を取得しますか？CCNP認定資格の対応試験は642-813です。642-813(Implementing Cisco IP Switched Networks)試験を通した後、642-813受験者は自身のレベルを証明することができます。
ITエリートのCCNP認定資格取得ために正確な認定準備資料を提供します。Testpassport 642-813受験参考書を提供して、気楽100％合格することができます。弊社の問題集を利用して、CCNP認定資格取得のは夢ではありません、そして、独学可能です。会社であれば、インタ-ネットの領域であれば、自己のレベルを証明するために、CCNP認定証を持った無ければなりません。
無料サンプルを提供して、買う前に、642-813無料デモを見られます。
http://pdf.testpassport.jp/642-813.pdf
1.Company uses layer 3 switches in the Core of their network. Which method of Layer 3 switching
uses a forwarding information base (FIB)?
A. Topology-based switching
B. Demand-based switching
C. Route caching
D. Flow-based switching
E. None of the other alternatives apply
Answer: A
2.You need to design the VLAN scheme for the Company network. Which two statements are true
about best practices in VLAN design? (Select two)
A. Routing should occur at the access layer ifvoice VLANs are utilized. Otherwise, routing should
occur at the distribution layer.
B. Routing should always be performed at the distribution layer.
C. VLANs should be localized to a switch.
D. VLANs should be localized to a single switch unlessvoice VLANs are being utilized.
E. Routing should not be performed between VLANs located on separate switches.
Answer: B,C
3.Refer to the exhibit. On the basis of the information provided in the exhibit, which two sets of
procedures are best practices for Layer 2 and 3 failover alignment? (Choose two.)
1
A. Configure the D-SW1 switch as the active HSRP router and the STP root for all VLANs.
Configure the D-SW2 switch as the standby HSRP router and backup STP root for all VLANs.
B. Configure the D-SW1 switch as the standby HSRP router and the STP root for VLANs 11 and
110. Configure the D-SW2 switch as the standby HSRP router and the STP root for VLANs 12 and
120.
C. Configure the D-SW1 switch as the active HSRP router and the STP root for VLANs 11 and
110. Configure the D-SW2 switch as the active HSRP router and the STP root for VLANs 12 and
120.
D. Configure the D-SW2 switch as the active HSRP router and the STP root for all VLANs.
Configure the D-SW1 switch as the standby HSRP router and backup STP root for all VLANs.
E. Configure the D-SW1 switch as the active HSRP router and the backup STP root for VLANs 11
and 110. Configure the D-SW2 switch as the active HSRP router and the backup STP root for
VLANs 12 and 120.
F. Configure the D-SW1 switch as the standby HSRP router and the backup STP root for VLANs
12a nd 120. Configure the D-SW2 switch as the standby HSRP router and the backup STP root
for VLANs 11 and 110.
Answer: C,F
4.If you needed to transport traffic coming from multiple VLANs (connected between switches), and
your CTO was insistent on using an open standard, which protocol would you use?
A. 802.11B
B. spanning-tree
C. 802.1Q
D. ISL
E. VTP
F. Q.921
Answer: C
5.Under what circumstances should an administrator prefer local VLANs over end-to-end VLANs?
A. Eighty percent of traffic on the network is destined for Internet sites.
B. There are common sets of traffic filtering requirements for workgroups located in multiple
buildings.
C. Eighty percent of a workgroup’s traffic is to the workgroup’s own local server.
D. Users are grouped into VLANs independent of physical location.
E. None of the other alternatives apply
Answer: A

发表评论：